氣體增壓泵是以壓縮空氣為動力源的一種活塞式增壓泵，當進氣時增壓氣控閥的閥芯往復切換工作，控制增壓泵活塞以極快的速度作往復動作，隨著輸出壓力的增高，活塞的往復速度減慢直停止，此時，增壓泵輸出的壓力恒定，能量消耗低，各部件停止工作；無/何種原因造成保壓回路壓力下降，增壓泵將自動啟動，補充泄露壓力，保持回路壓力恒定。大驅動氣壓為8bar。 1-驅動空氣入口；2-驅動空氣管路；3-氣動活塞；4-頂部撞針；5-先導閥口；6-換向閥；7-底部撞針；8-先導排氣口；9-消聲器；10-入口單向閥；11-出口單向閥氣動氣6增壓泵一般用于產品氣壓測試、提升工廠局部氣源壓力等，在次使用前，須詳細閱讀產品相關使用說明，切勿憑感覺操作。使用時，注意以下事項等，可用的更久。 1、使用的環境粉塵不能太多，因?yàn)闅鈩?dòng)氣體增壓泵上的呼吸孔可能會把雜志吸入泵的腔體內6，進而可能會導致其上的密封圈機缸筒劃傷等情況的發生，大大的縮減應有的使用壽命年限。 2、如有條件的，可通過加配油水分離器來達到過濾掉空氣驅動氣源中的雜質以及水分等，這對于延長綜合使用年限都是很有幫助的。

A gas booster pump is a piston type booster pump that uses compressed air as the power source. When the air is intake, the valve core of the booster gas control valve switches back and forth, controlling the booster pump piston to perform reciprocating action at an extremely fast speed. As the output pressure increases, the reciprocating speed of the piston slows down until it stops. At this time, the output pressure of the booster pump is constant, energy consumption is low, and all components stop working; If there is no reason for the pressure drop in the pressure maintaining circuit, the booster pump will automatically start to supplement the leakage pressure and maintain a constant circuit pressure. The driving pressure is 8 bar. 1. Drive air inlet; 2- Drive air pipeline; 3- Pneumatic piston; 4-Top firing pin; 5- Pilot valve port; 6-directional valve; 7- Bottom firing pin; 8- Pilot exhaust port; 9- Silencer; 10- Inlet one-way valve; 11. The outlet one-way valve pneumatic 6 booster pump is generally used for product air pressure testing, improving local air supply pressure in the factory, etc. Before the first use, it is necessary to carefully read the relevant product instructions and not operate based on intuition. When using, pay attention to the following items, etc., for longer use. 1. The environmental dust used should not be too much, as the breathing hole on the pneumatic gas booster pump may suck the magazine into the pump chamber, which may cause scratches on the sealing ring and cylinder barrel, greatly reducing the expected service life. 2. If conditions permit, an oil-water separator can be added to filter out impurities and moisture in the air driven gas source, which is helpful for extending the comprehensive service life.

氣體增壓系統氣體增壓系統是根據客戶的實際需要，將增壓泵及各部件裝配在管式框架內或封閉箱體內，結構緊湊，使用方便。壓力表、閥、壓力調節器均為面板安裝。通過設定氣壓調節器可調節輸出壓力。到達設定壓力時泵自動停止，壓力下降時恢復工作。3－8bar普通潔凈壓縮空氣驅動，氣體工作壓力可達80MPa,如果需更高壓力選用雙驅動頭增壓

The gas boosting system is based on the actual needs of customers, where the booster pump and various components are assembled in a tubular frame or enclosed box, with a compact structure and convenient use. The pressure gauge, valve, and pressure regulator are all panel mounted. The output pressure can be adjusted by setting the air pressure regulator. When the set pressure is reached, the pump automatically stops and resumes operation when the pressure drops. 3-8bar ordinary clean compressed air drive, gas working pressure can reach 80MPa, if higher pressure is required, double drive head boosting is selected

產品典型應用：

Typical application of the product:

1.用于工廠壓縮空氣的二次增壓，氮?dú)?、氫氣高壓反?yīng)釜的充裝，及其它需各種高壓氣體的場合。

1. Used for secondary pressurization of compressed air in factories, filling of high-pressure reaction vessels for nitrogen and hydrogen, and other situations that require various high-pressure gases.

2.氣體輔助注塑，及其輔助注塑中的高壓氮?dú)獬錃?/p>

2. Gas assisted injection molding and high-pressure nitrogen inflation in assisted injection molding

3.閥門、管件，冷凝管、空調盤管的氣密性測試，閥門及井口裝置水中冒泡試驗

3. Air tightness testing of valves, fittings, condensate pipes, and air conditioning coils, as well as water bubbling testing of valves and wellhead safety devices

4.航空航天附件維修后的靜態動態測試，閥門校定

4. Static and dynamic testing of aerospace accessories after maintenance, and calibration of safety valves

5.汽車制動系統測試，通訊電纜充氣設備

5. Automotive brake system testing, communication cable inflation equipment

6.飛機輪胎和液壓蓄能器充氮?dú)猓邏簹怏w系統和儀器的測試

6. Testing of aircraft tires and hydraulic accumulators filled with nitrogen, high-pressure gas systems, and instruments

7.去礦化作用，如反滲透作用及脫鹽作用

7. Demineralization processes, such as reverse osmosis and desalination

8.提供壓力以測驗或校準天然氣元件

8. Provide pressure to test or calibrate natural gas components

9.記錄井下流體深度聲波設備的動力，及高壓氣體流形態研究。

9. Record the power of downhole fluid depth acoustic equipment and study the morphology of high-pressure gas flow.

本文來自：氣體增壓泵更多的內容請點擊：http://www.dtgl.com.cn我們將會為您提問的問題提供一個滿意的服務，歡迎您的來

This article is from: Gas Booster Pump. For more information, please click on: http://www.dtgl.com.cn We will provide you with a satisfactory service for the questions you ask. Welcome to come